QCS-3汽車內飾阻燃試驗箱/內飾材料燃燒試驗儀
QCS-3 automotive interior materials combustion test device
1、簡介
A brief introduction
QCS-3型汽車內飾材料燃燒試驗裝置，根據標準GB8410-2006《汽車內飾材料的燃燒特性》的規定技術要求而設計的，同時符合美國汽車安全技術法規FMVSS 571.302等標準規定的模擬燃燒性能安全試驗項目、德標DIN7520《汽車內飾材料的燃燒特性》及TL1010《汽車內飾材料燃燒特性》的相關要求，用于鑒別轎車、多用乘客車、載貨汽車和客車內飾材料水平燃燒特性。
QCS-3 type automotive interior material combustion test device, according to national standard GB8410-2006 "combustion characteristics of automotive interior materials" design, and in accordance with the United States automotive safety technology regulations FMVSS 571.302 and other standards for the simulation of safety testing project, German standard DIN7520 "automotive interior materials combustion characteristics" and TL1010 "automotive interior material combustion characteristics" related requirements, for the identification of cars, multi passenger car, truck and passenger car interior material level combustion characteristics.
2、工作條件及主要技術指標
Two, working conditions and the main technical indicators
1.環境溫度：-5℃-30 ℃
1 environmental temperature: -5 -30
2.相對濕度：≤ 85%
2 relative humidity: less than 85%
3.供電電壓：220V+ 10%、50HZ,功率：100W
3 power supply voltage: 220V+ 10%, 50HZ, power: 100W
4.氣源：液化石油氣
4 gas source: liquefied petroleum gas
5.秒表精度不低于0.5s
5 stopwatch accuracy is not less than 0.5s
6.本生燈（即燃燒器）對試樣施加火焰15s
6 the burner lamp (i.e., burner) is applied to the sample by applying flame 15s
7.本生燈管內徑9.5mm+ 0.1mmm，長約100mm
7 the inner diameter of the tube is 0.1mmm 9.5mm+, about 100mm
8.試驗傾角：本生燈90°垂直對著水平放置的樣品燃燒
8 test angle: the 90 degree of the lamp is burning with the sample placed in the horizontal level.
9.火焰高度：20mm± 2mm 到100mm±2mm可調(1般調為38mm)
9 flame height: 20mm + 2mm + 100mm + 2mm adjustable (generally 38mm)
10.施焰時間：0-999.9s±0.1s可調（1般選擇為15s)
10 flame time: 0-999.9s + 0.1s adjustable (general choice for 15s)
11.續燃時間：0-999.9s±0.1s，觀察火焰達到標線后手動開始、手動暫停
11 afterflame time: 0-999.9s + 0.1s, observe the flame to the first line after the manual start, manual pause
12.燃燒氣體：液化石油氣或煤氣
12 combustion gas: liquefied petroleum gas or gas
13.溫度范圍：0～200℃（顯示測試狀態下工作室內部溫度）
13 temperature range: 0 ~ 200 (show the internal temperature of the studio in the test condition)
3、設備組成
Three, equipment composition
1.設備分控制部分與通風櫥1體、燃燒室內置。
1 the equipment control section and a hood, built-in one combustion chamber.
2.點火自動控制系統
2 ignition automatic control system
3.試驗過程：試驗程序自動控制
3 test procedure: automatic control of test procedure
4.自動進排氣系統（燃氣自動開啟、自動關閉）
4 automatic air intake and exhaust system (gas automatic opening, automatic shutdown)
5.計時系統：燃燒計時器、余焰計時器
5 time system: burning timer, residual flame timer
6.U型支架：上支架有6個銷孔，下支架對應有6個銷子，并布有線徑為0.25mm及間距為25mm的耐熱金屬支撐線
6.U type bracket, bracket has six pin hole, lower bracket corresponding to have six pin, and cloth cable diameter of 0.25mm and spacing 25mm heat-resistant metal support line
7.試驗支架第3標線距第2標線距離為154mm
7 test support third from the second distance 154mm marking marking
8.耐熱金屬絲槽 0.5mm X 0.5mm 間距 25mm
8 X 0.5mm 0.5mm spacing 25mm
9.金屬絲長度大于110mm,每25mm有7~8個光圓齒
9 metal wire length is greater than 110mm, each 7~8 has a 25mm light circle tooth
10.溫度數顯，測量范圍0-200℃
10 temperature display, measuring range of 0-200
11.火焰標尺精度：0.1mm
11 flame scale accuracy: 0.1mm
12.設備外形尺寸：長 寬 高 1300 650 1200（鋼板靜電噴涂材質）
12 equipment appearance size: length width high 1300 650 1200 (steel plate electrostatic spraying material)
4、試樣尺寸：長356mm、寬100mm、厚≤ 13mm
Four, sample size: length 356mm, width 100mm, thickness of less than 13mm
5、設計標準
Five, design standards
GB8410-2006
GB8410-2006
FMVSS 571.302等標準規定的模擬燃燒性能安全試驗項目
FMVSS 571.302, and other standards for the simulation of the performance of the fire safety test project
DIN7520《汽車內飾材料的燃燒特性》
DIN7520 "combustion characteristics of automotive interior materials"
TL1010汽車內飾材料燃燒特性
TL1010 automotive interior material combustion characteristics
符合標準：GM6090M、DIN75200、GM9070P、FMVSS 302、JIS D 1201、JASO M403 、ISO 3795、ASTM D5132、QB／T 2729-2005
Meet the standards: DIN75200, GM9070P, GM6090M, FMVSS 302, D JIS 1201, M403 JASO, ISO 3795, D5132 ASTM, QB / 2729-2005 T