| Mechanical |
| Format | Standard profile, half length, 8-lane PCI Express card |
| Cooling method | Air cooling, fan-cooled heatsink |
| Mounting | For insertion in a standard height, 8-lane or higher, PCI Express card slot |
| Connectors | - 'A', 'B', 'C', 'D' on bracket:
- 4x Micro-BNC female connectors
- CoaXPress host interface
- 'EXTERNAL I/O' on bracket:
- 26-pin 3-row high-density female sub-D connector
- I/O lines and power output
- 'INTERNAL I/O 1' and 'INTERNAL I/O 2' on PCB:
- 2x 26-pin 2-row 0.1" pitch pin header with shrouding
- I/O lines and power output
- 'I/O EXTENSION' on PCB:
- 26-pin 2-row 0.05" pitch pin header with shrouding
- I/O extension lines and power output
- 'AUXILIARY POWER INPUT' on module:
- 6-pin PEG power socket
- 12 VDC power input for PoCXP camera(s) and I/O power
- 'C2C-LINK' on module:
- 6-pin 2-row 0.1-in header
- Card to card link
|
| LED indicators | - 'A', 'B', 'C', 'D' on bracket:
- Bi-color red/green LEDs
- CoaXPress Host connector indicator
- 'FPGA STATUS LAMP' on PCB:
- Bi-color red/green LED
- FPGA status indicator
- 'BOARD STATUS LAMP' on PCB:
- Bi-color red/green LED
- Board status indicator
|
| Switches | 'RECOVERY' on card PCB:- 3-pin 1-row 0.1" header
- Firmware emergency recovery
|
| Dimensions | L 167.65 mm x H 111.15 mm L 6.6 in x H 4.38 in |
| Weight | 196 g, 6.91 oz |
| Host bus |
| Standard | PCI Express 3.0 |
| Link width | - 8 lanes
- 1 lane, 2 lanes or 4 lanes with reduced performance
|
| Link speed | - 8.0 GT/s (PCIe 3.0)
- 5.0 GT/s (PCIe 2.0) with reduced performance
|
| Maximum payload size | 512 bytes |
| DMA | 32- and 64-bit |
| Peak delivery bandwidth | 7,800 MB/s |
| Effective (sustained) delivery bandwidth | 6,700 MB/s (Host PC motherboard dependent) |
| Power consumption | Typ. 17.1 W (7.3 W @ +3.3V,9.8 W @ +12V), excluding camera and I/O power output |
| Camera / video inputs |
| Interface standard(s) | CoaXPress 1.0, 1.1, 1.1.1 and 2.0 |
| Connectors | Four micro-BNC 75 Ohms (also known as HD-BNC™) CXP-12 |
| Status LEDs | One CoaXPress Host connection status LED per connection |
| Number of cameras | - Area-scan cameras:
- One 1- or 2- or 4-connection camera
- Four 1-connection cameras
- Line-scan cameras:
- One 1- or 2- or 4-connection camera
|
| Maximum aggregated camera data transfer rate | 50 Gbit/s (5,000 MB/s) |
| Supported CXP down-connection speeds | 1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3), 5 GT/s (CXP-5), 6.25 GT/s (CXP-6), 10.0 GT/s (CXP-10), and 12.5 GT/s (CXP-12) |
| Supported CXP up-connection speeds | - Low-speed 20.83 Mbps (CXP-1 to CXP-6)
- Low-speed 41.66 Mbps (CXP-10, CXP-12)
|
| Number of CXP data streams (per camera) | 1 data stream per camera |
| Maximum CXP stream packet size | 16,384 bytes |
| PoCXP (Power over CoaXPress) | - PoCXP Safe Power:
- 17 W of 24V DC regulated power per CoaXPress connector
- PoCXP Device detection and automatic power-on
- Overload and short-circuit protections
- On-board 12V to 24V DC/DC converter
- A +12V power source must be connected to the AUXILIARY POWER INPUT connector using a 6-pin PEG cable
|
| Camera types | - Area-scan cameras:
- Grayscale and color (YCbCr, YUV, RGB and Bayer CFA)
- Single-tap (1X-1Y) progressive-scan
- Line-scan cameras and contact imaging sensors:
|
| Camera pixel formats supported | Raw, Monochrome, Bayer, RGB, and RGBA (PFNC names):- Raw
- Mono8, Mono10, Mono12, Mono14, Mono16
- BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG
- RGB8, RGB10, RGB12, RGB14, RGB16
- RGBA8, RGBA10, RGBA12, RGBA14, RGBA16
- YCbCr601_422_8, YCbCr601_422_10
- YCbCr709_422_8, YCbCr709_422_10
- YUV422_8, YUV422_10
|
| Area-scan camera control |
| Trigger | - Precise control of asynchronous reset cameras, with exposure control.
- Support of camera exposure/readout overlap.
- Support of external hardware trigger, with optional delay and trigger decimation.
|
| Strobe | - Accurate control of the strobe position for strobed light sources.
- Support of early and late strobe pulses.
|
| Line-scan camera control |
| Scan/page trigger | - Precise control of start-of-scan and end-of-scan triggers.
- Support of external hardware trigger, with optional delay.
- Support of infinite acquisition, without missing line, for web inspection applications.
|
| Line trigger | - Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation.
- Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%.
- Rate Divider tool
|
| Line strobe | - Accurate control of the strobe position for strobed light sources.
|
| On-board processing |
| On-board memory | 2 GB |
所有評論僅代表網(wǎng)友意見，與本站立場無關。