通過CBNR通訊模塊，可以輕松地完成CONTROLNET控制網絡的通訊功能。

　　3.3控制室計算機

　　控制室計算機采用力控組態軟件來完成實時控制和監測功能。

　　三、控制方案概述

　　 儀表和動力設備均設有兩種控制方式，即現場手動控制方式和集中控制方式，以集中控制方式為主。集中控制主要在值班控制室的PLC控制臺上由值班操作員進行。集中控制方式又分為自動控制方式和手動控制方式。雖然在中控制室也可對現場儀表和設備進行必要的直接操作控制，但控制室主要是執行管理和監督功能和對重要設備的運行及停止給出允許指令。

　　1 調節池控制

　　1.1 進入污水處理廠的污水首*入調節池，以對水量和水質進行調節。調節池內的4個潛水泵對應有4個電動碟閥。潛水泵和電動碟閥的控制分手動方式和自動方式。在自動方式下，當調節池水位高于75%時，4臺潛水泵和其對應的電動蝶閥全都起動和打開。當調節池水位在50~75%時，只起動3臺潛水泵并打開和其對應的3臺電動蝶閥。當調節池水位在25~50%時，只起動2臺潛水泵并打開和其對應的2臺電動蝶閥。當調節池水位在低于25%時，只起動1臺潛水泵并打開和其對應的1臺電動蝶閥。當調節池水位低于低限設定值時潛水泵停泵，電動蝶閥全關。在手動方式下，操作員可根據情況對每臺潛水泵和其對應的電動蝶閥單獨操作。

　　1.2 調節池的攪拌機可根據潛水泵運行信號自動起動，也可由操作員手動起動。自動起動方式下，攪拌機可分組起動或全部起動。手動起動方式下，每臺攪拌機均可單獨操作。

　　1.3 流量計FI-101增加進水流量累計軟功能塊，對進水流量進行累計，數據存在監控計算機的數據庫中，可隨時調用和打印。

　　2 細格柵間與沉砂池的控制

　　2.1 細格柵間設回轉式機械格柵2 臺（1用1備）。細格柵間前后各裝有啟閉機和液位差計。去渣設備可根據液位差（如大于某設定值）或定時自動起動，也可由操作員手動起動。

　　2.2 沉砂池的行車式刮砂機和砂泵可根據設定的時間自動同步運行或由操作員手動控制運行。當刮砂機在池上往返運行一個來回后，刮砂機和砂泵自動停機。

　　2.3 流量計FI-102增加進水流量累計軟功能塊，對進水流量進行累計，數據存在監控計算機的數據庫中，可隨時調用和打印。

　　3 初沉池及配水井的控制

　　3.1 初沉池配水井有3個啟閉機，2個啟閉機分別控制到2個初沉池的進水，第3個啟閉機控制跨越初沉池的旁路。

　　3.2 初沉池裝有液位計，以指示其液位變化。當液位超過設定的上，自動打開啟閉機將水送入對應的A/O生化反應池。

　　3.3 刮泥機的運行狀態由PLC進行監控。刮泥機可自動或手動運行。

　　4 廠區排水泵池的控制

　　4.1 廠區排水泵池的控制分手動控制方式和自動控制方式。

　　4.2 在自動控制方式下，當廠區排水泵池水位在50~75%時， 起動一臺排水泵。當廠區排水泵池水位在75%以上時，起動另一臺排水泵。

　　4.3 當廠區排水泵池水位回落到75%以下時，停一臺排水泵。當廠區排水泵池水位回落到50%以下時，停另一臺排水泵。

　　4.4 在手動控制方式下，操作員可任一排水泵的起、停。

　　5 A/O生化反應池與鼓風機的控制

　　5.1 每座生化反應池分五個廊道，每個廊道都裝有溶解氧指示儀表。在好氧段有送風管，送風管入口設有電動蝶閥。操作員可根據各廊道溶解氧指示儀的指示值決定該廊道電動蝶閥的開啟。

　　5.2 在絕氧段設水下攪拌器3臺。水下攪拌器設定為“自動"運行狀態后將連續運行，除非故障或手動停機。motor, maintenance-free use. Solid state switch can protect the short circuit of load, over current of motor, three-phase unbalance and under voltage of power supply. The operation is simple, the status display is intuitionistic, the protection is quick and reliable. 9.3 The use of pneumatic transmitter, the use of digital pressure transformer pressure signal collection, pressure value display intuitive, accurate action value, easy to adjust calibration. 9.4 PLC is easy to operate, and the logic control circuit is realized by software. It can change the control flow according to the operator's requirement at any time to meet the requirement of field operation. 9.5 THE IMPROVEMENT OF ALARM SYSTEM: low-voltage machine monitoring system alarm display clear, operating personnel through the light word display, can directly understａnd the fault point, so as to deal with quickly. Full range of protection. 9.6 improve the Working Environment of PLC control cabinet layout compact, reasonable structure, disk beautiful and generous, running display at a glance, easy to control and operate. 9.7 Remote Monitoring Plc can establish communication with the host computer at any time, and upload the collected switch data and analog data to the remote ALP workstation for remote monitoring. The upper computer can also transmit control instructions to realize the remote control of the low-pressure machine. 10. New System running effect: 10.1 PLC used to eliminate the original control system fault factors, greatly improve the auxiliary equipment of our factory automation control level. Since it was put into operation in June, 1999, there has been no failure record of low-pressure machine control system in operation defect record book. 10.2 many times in time to reflect the mechanical failure of the low-pressure machine, accurate protection of the operation of the main mechanical equipment. 10.3 the control system has achieved inspection-free performance. Since put into operation has never carried on the overhaul maintenance, reduced the overhaul workload greatly, saved the massive overhaul expense. 10.4 the operation mode of the system is completely transplanted to the original system operation mode, and the operator can operate the system directly without training.