| INPUT | ||
| Voltage | 115/230 VAC ± 10%, User selection | |
| Frequency | 50/60 Hz ± 5% | |
| Fuse | 6.3 Amp 250V Slo-Blo | |
| DIELECTRIC WITHSTAND TEST MODE | ||
| Output Rating | 5 KV @ 20mA AC | |
| 6 KV @ 5 mA DC | ||
| Output Adjustment | Range: | 0-5 KV AC, 0-6 KV DC |
| Resolution: | 10 volt/step | |
| Accuracy: | ± （2% of setting + 5 volts） | |
| Voltage Display | Range: | 0 - 5 KVAC / 0-6KV DC |
| Resolution: | 10 volt/step | |
| Accuracy: | ± （2% of reading + 10 volts） | |
| HI / LO -Limit AC | Range: | 0.00 - 20.00 mA |
| Resolution: | 0.01 mA/step | |
| Accuracy: | ± （2% of setting + 0.02 mA） | |
| AC Current Display | Range: | 0.00 - 20.00 mA |
| Resolution: | 0.01 mA/step | |
| Accuracy: | ± （2% of reading + 0.02 mA） | |
| HI / LO -Limit DC | Range: | 0.00 - 5.00 mA |
| Resolution: | 0.01 mA/step | |
| Accuracy: | ± （2% of setting + 0.02 mA） | |
| DC Current Display | Range: | 0.00 - 5.00 mA |
| Resolution: | 0.01 mA/step | |
| Accuracy: | ± （2% of reading + 0.02 mA） | |
| Failure Detector | Audible and Visual | |
| Output Ripple | < 5% （6KVDC/5 mA at Resistive Load） | |
| Discharge Time | ≦ 200 ms | |
| Maximum Capacitive Load in DC Mode | 1µF < 1KV , 0.75µF < 2KV, 0.5µF < 3KV, 0.08µF < 4KV, 0.04µF < 5KV, 0.01µF < 6KV | |
| AC Wave Form | Sine wave Distortion : < 2% THD ; Crest Factor= 1.3 – 1.5 | |
| Output Frequency | Range: | 60 or 50 Hz, User Selection |
| Output Regulation | ± （1 % of output + 5 volts） from no load to full load | |
| Dwell Timer | Range: | 0, 0.2 - 999.9 sec, （0 = Constant） |
| Resolution: | 0.1 sec increments | |
| Accuracy: | ± （0.1% + 0.05 sec） | |
| Ramp Timer | Range: | 0.1 - 999.9 sec |
| Resolution: | 0.1 sec increments | |
| Accuracy | ± （0.1% + 0.05 sec） | |
| INSULATION RESISTANCE TEST MODE | ||
| Output Voltage | Range: | 100 - 1000 Volts DC |
| Resolution: | 1 volt/step | |
| Accuracy: | ± （2% of reading + 5 volts） | |
| Voltage Display | Range: | 0 - 1000 V |
| Resolution: | 1 volt/step | |
| Accuracy: | ± （2% of reading + 2 counts） | |
| Resistance Display | Range: | 1 - 1000 MΩ （4 Digit, Auto Ranging） |
| Resolution: | 0.01/0.1 MΩ | |
| Accuracy: | ± （3% of reading + 2 counts） at test voltage > 500V | |
| ± （7% of reading +2 counts） at test voltage < 500V | ||
| HI-Limit | Range: | 0, 1 - 1000 M Ω （0 = Off） |
| LO-Limit | Range: | 1 - 1000 M Ω |
| Delay Timer | Range: | 0, 0.5 - 999.9 sec （0 = Constant） |
| Resolution: | 0.1 sec/step | |
| Accuracy: | ± （0.1% + 0.05 sec） | |
| GROUND BOND TEST MODE | ||
| Output Voltage | Range: | AC 6 volts Max. |
| Output Frequency | Range: | 60 or 50 Hz, User Selection |
| Accuracy: | ±0.1% | |
| Output Current | Range: | 3.0 - 30.0 Amps AC |
| Resolution: | 0.1 Amp/step | |
| Accuracy : | ± （2 % of setting + 0.1A） | |
| Current Display | Range: | 0.0 - 30.0 Amps |
| Resolution: | 0.1 Amp/step | |
| Accuracy: | ± （3 % of reading + 0.1A） | |
| Resistance HI-Limit | Range: | 0 - 510 mΩ |
| Resistance Display | Range: | 0 – 510 mΩ for 0.0 – 10.0 Amps |
| 0 – 200 mΩ for 10.1 – 25.0 Amps | ||
| 0 – 150 mΩ for 25.1 – 30.0 Amps | ||
| Resolution: | 1 mΩ/step | |
| Accuracy: | ± （2 % of Setting + 2 mΩ ） | |
| Dwell Timer | Range: | 0, 0.5 - 999.9 sec （0 = Constant） |
| Resolution: | 0.1 sec/step | |
| Accuracy: | ± （0.1% + 0.05 sec） | |
| Lead Resistance Offset | Max. Offset Capability: | 100 mΩ |
| Resolution: | 1 mΩ / step | |
| Accuracy: | ± （2 % of Setting + 2 mΩ ） | |
| GENERAL SPECIFICATIONS | ||
| PLC Remote Control | Input - Test, Reset, Interlock & Recall Memory 1 - 6 | |
| Output - Pass, Fail, Test-in-Process | ||
| Memory | Allows storage of up to 6 different test programs and 6 step/each memory and single step mode. | |
| Security | Lockout capability to avoid unauthorized access to test set-up programs. | |
| Calibration | Software and adjustments are made through front panel. | |
| Mechanical | Bench or rack mount with tilt up front feet. | |
| Optional Arc Detection Hardware | ACW and DCW; Software adjustable Arc Level 0-9 | |
| Dimension | 280（W） x 89（H） x 430（D） mm | |
| Weight | 33 lbs. （15 kg） | |
所有評論僅代表網友意見，與本站立場無關。